loading

Classification and description of Tenon machines for processing wood products

by:Gewinn     2020-03-18
The double-head Tenon tenoning machine is actually a combination of two single-Head straight Tenon tenoning machines located on both sides of the workpiece for Tenon opening at both ends at the same time. The workpiece is pressed on two synchronous track feeding devices to feed to the cutter shaft. The width of mortise can be adjusted by moving the Movable Column. This mortise machine has high productivity and is suitable for mass production. Dovetail tenoning machine is used to process through dovetail tenon or semi-hidden dovetail Tenon. The dovetail-shaped milling cutter is installed on the vertical spindle, and the two sheet metal workpieces are vertically clamped on the workbench. The Workbench moves along the 'U'-shaped track along the profile, and the Yin-Yang dovetail tenon is processed at the same time. There is also a fixed table, the knife shaft for the 'U' shaped trajectory movement. Equipment requirements (1)The cantilever is firmly fixed and the V-shaped guide rail has no defects; (2) Cantilever adjustment device should be intact and locked reliably; (3) , Bracket and the positioning on the bracket, the stop device should be intact, accurate positioning, reliable stop; (4) . The limit device of the front and back sliding of the bracket should be sensitive and reliable; (5)Roll-on installation should be firm and flexible. The ball is broken, missing or the rolling rail is loose. It is strictly prohibited to use it. (6), Saw shaft should be no obvious deformation or damage; (7), Flange should be no cracks or damage; (8)The machine tool shall be protected from grounding (Zero), And there are obvious signs; (9), Saw blade protective cover should be intact, can adjust; (10)The Workbench adjustment device is in good condition and the locking is reliable; (11) , Saw blade protective cover, chip cover, Belt protective cover should be intact and firm; Comb Tenon tenoning machine, including rack, bed, Workbench, two cutting saws and two comb knives, two cutting saws and two comb knives are equipped with bed bodies and distributed on both sides of the workbench; The Workbench is placed on the guide rail of the bed. Its structural feature is that the Workbench is equipped with conveyor belts driven by motors. The two sides of the Workbench are respectively equipped with left and right moving cylinders, and the left and right moving cylinders are respectively equipped with pressure gauges, the two pressure gauges are respectively connected with the pressure cylinder which can lift up and down, and the left and right motion cylinder moves left and right to drive the left and right moving pressure gauge and the pressure cylinder which can lift up and down on it to move; There are adjustable grids on both sides of the Workbench which are located in the pressing cylinder. One adjustable grid is located at the end of the material outlet, and the other adjustable grid is located at the end of the material inlet; An oil cylinder is set in the middle of the guide rail, and the wood is discharged from the conveyor belt and then pushed through the oil cylinder to discharge in place. Through the pressure cylinder and the left and right movement cylinder that can rise and fall, the left and right, up and down movement is accurate and controlled freely. The working characteristics of the slitting lathe are that the spring Chuck in the main shaft holds the bar for rotation and axial feed movement, and the cutter for radial movement; If the tool is still, the spindle box is fed into the turning outer circle; While the headstock is still, the radial feeding of the cutter is the turning groove, forming or cutting; When the two are in compound motion at the same time, the work such as car cone or forming surface can be completed. The cycle process of the machine tool is generally for the spindle clamping bar to carry out various cutting work, and then cut off. After the parts are cut off, the spring Chuck is released and the spindle box is returned. At this time, the bar stock is supported on the cutting knife by the power of the heavy hammer in the feeding rack. After the spindle box is returned to the original position, the spring Chuck is clamped, then the cutting knife is returned, and then the next cycle is started. When a bar is used up, the machine tool will automatically stop and ensure the integrity of the last part through the action of two parallel safety switches on the feeding rack and behind the bed.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...