Indonesia
Deutsch
Better Touch Better Business
Conclusion woodworking machinery safety operation requirements
by：Gewinn
2020-09-23
Summary of woodworking machinery safety operation requirements
the following is an introduction to the safe operation requirements of woodworking machinery:
a before operation, the safety of the operation requirements:
1, wear good clothes and good hair cap, wear safety shoes, wear the necessary labor protection articles, such as dust masks, goggles, ear protector.
2, check the work environment, flat ground to clean, neatly stacked wood, not on the walkway. Illuminance in the workplace should comply with the design requirements.
3, check the sharp knives, have without gap, crack, or saw blade presence of dust adhesion, found the problem, handle in time.
4 to slowly inserted into the main shaft, cutter, turn the nut by hand, and then tightened with a wrench.
5, to the sliding parts and hand handle in the rotating mechanism such as bearings, gears, chain into appropriate oil, look for loose nut and screw everywhere.
6, identification of stop position at the same time, to check whether the fixation.
7, check whether the v belt is damaged, the guard is damaged, whether the set screw is loose.
8, check whether there is any abnormal on safety device, can confirm the brake brake within 10 s.
2, the operation of the safety operation requirements:
1, the boot after, can feed after sawing machine to achieve the highest speed. Feed rate should be based on wood material; With or without knots, cracks and processing thickness control. Feeding to steady, slow, not too hard, in case of damage to the saw blade, saw blade, and cuts.
2, feed, and cutting tools should maintain a certain distance, use of push stick when necessary.
3, shall not adjust the guide in the operation.
4, operation of the circular saw, feeding should cooperate with and work well. Feeding worker stood on the blade profile. Wood jig, should stop immediately, after sawing curf insert wedge extended road continue to operate.
5, the chip on both sides of the saw blade, bark, wood chips and other sundry, should be removed with sticks, may not be directly by hand to remove, so as to avoid hurting hands. Mechanical operation of the
6, about 30 min, cut off power supply, touch the spindle bearings are fever, such as high temperature should be shut down, report the relevant personnel.
7, check the safety device fixed screw, nut loose.
8, material to pin wood, in case the back jump cuts.
the following is an introduction to the safe operation requirements of woodworking machinery:
a before operation, the safety of the operation requirements:
1, wear good clothes and good hair cap, wear safety shoes, wear the necessary labor protection articles, such as dust masks, goggles, ear protector.
2, check the work environment, flat ground to clean, neatly stacked wood, not on the walkway. Illuminance in the workplace should comply with the design requirements.
3, check the sharp knives, have without gap, crack, or saw blade presence of dust adhesion, found the problem, handle in time.
4 to slowly inserted into the main shaft, cutter, turn the nut by hand, and then tightened with a wrench.
5, to the sliding parts and hand handle in the rotating mechanism such as bearings, gears, chain into appropriate oil, look for loose nut and screw everywhere.
6, identification of stop position at the same time, to check whether the fixation.
7, check whether the v belt is damaged, the guard is damaged, whether the set screw is loose.
8, check whether there is any abnormal on safety device, can confirm the brake brake within 10 s.
2, the operation of the safety operation requirements:
1, the boot after, can feed after sawing machine to achieve the highest speed. Feed rate should be based on wood material; With or without knots, cracks and processing thickness control. Feeding to steady, slow, not too hard, in case of damage to the saw blade, saw blade, and cuts.
2, feed, and cutting tools should maintain a certain distance, use of push stick when necessary.
3, shall not adjust the guide in the operation.
4, operation of the circular saw, feeding should cooperate with and work well. Feeding worker stood on the blade profile. Wood jig, should stop immediately, after sawing curf insert wedge extended road continue to operate.
5, the chip on both sides of the saw blade, bark, wood chips and other sundry, should be removed with sticks, may not be directly by hand to remove, so as to avoid hurting hands. Mechanical operation of the
6, about 30 min, cut off power supply, touch the spindle bearings are fever, such as high temperature should be shut down, report the relevant personnel.
7, check the safety device fixed screw, nut loose.
8, material to pin wood, in case the back jump cuts.
Custom message
