Indonesia
Deutsch
Better Touch Better Business
Second-hand woodworking equipment, woodworking machinery electronic saw matters needing attention for normal operation
by：Gewinn
2020-09-26
Second-hand woodworking equipment
1, after feeding device program-controlled push board operation shoulds not be too fast, program-controlled push board run ( For operator) Speed is greater than 25 m/min will shut down automatically advance
2, program-controlled push board biggest promote the height is 80 mm, ban transfinite propulsion
3, the owner saw use 380 mm diameter circular saw blades, the main saw blade is highest rose to 95 mm, maximum cutting thickness is 80 mm, it is forbidden to overrun sawing, transfinite sawing can lead to damage of equipment or saw blade
4, according to the cutting thickness and reasonable adjustment saw the car running cutting speed, adjusting range in 10 & ndash; — More than 80 m/min, sawing sawing zhang slow speed, cutting should be reasonable to reduce the speed, hard wood sawing particieboard sawing speed should be within 25 mm - 70 80 m/min, between 25 - sawing Within 60 mm saw speed should be in the 50 - Between 70 m/min, sawing 60 mm to 80 mm thickness when the fastest shall not exceed 40 m/min, lest cause saw blade moves equipment damage and avoid cutting quality problem, reasonably adjust the sawing speed in order to achieve the best effect of production
5, floating on the stage in front of the note to smoothly so as not to cause scratches, more can't hit side by feet and clamp
6, cutting the workpiece one-time place, start to keep out for the cause of the program, so as to avoid crushed cut
7, host, hand pay close attention to the equipment running status, when there is abnormal sound, abnormal vibration and other abnormal downtime check in time, and report to the leadership or equipment maintenance
8, replace the saw blade when replacing new saw blade, in particular, must be removed sawtooth protection film before installation of saw blade, such as not clear protective film can make cutting resistance, damage to equipment and saw blade
9, floating above it is prohibited to break a small wood, more than expected, so as not to damage the mesa sheet caused by the scratch
10, stick bar code must be used when brush dust, avoid the barcode adhesive is not strong to the next working procedure missing
11, after feeding the stack must be neat, avoid damage to the pinch clamp
we promise second-hand woodworking equipment with high quality products, perfect service, welcome friends from all walks of life come to dongguan, the forest industry machinery to visit, guidance and business negotiation.
1, after feeding device program-controlled push board operation shoulds not be too fast, program-controlled push board run ( For operator) Speed is greater than 25 m/min will shut down automatically advance
2, program-controlled push board biggest promote the height is 80 mm, ban transfinite propulsion
3, the owner saw use 380 mm diameter circular saw blades, the main saw blade is highest rose to 95 mm, maximum cutting thickness is 80 mm, it is forbidden to overrun sawing, transfinite sawing can lead to damage of equipment or saw blade
4, according to the cutting thickness and reasonable adjustment saw the car running cutting speed, adjusting range in 10 & ndash; — More than 80 m/min, sawing sawing zhang slow speed, cutting should be reasonable to reduce the speed, hard wood sawing particieboard sawing speed should be within 25 mm - 70 80 m/min, between 25 - sawing Within 60 mm saw speed should be in the 50 - Between 70 m/min, sawing 60 mm to 80 mm thickness when the fastest shall not exceed 40 m/min, lest cause saw blade moves equipment damage and avoid cutting quality problem, reasonably adjust the sawing speed in order to achieve the best effect of production
5, floating on the stage in front of the note to smoothly so as not to cause scratches, more can't hit side by feet and clamp
6, cutting the workpiece one-time place, start to keep out for the cause of the program, so as to avoid crushed cut
7, host, hand pay close attention to the equipment running status, when there is abnormal sound, abnormal vibration and other abnormal downtime check in time, and report to the leadership or equipment maintenance
8, replace the saw blade when replacing new saw blade, in particular, must be removed sawtooth protection film before installation of saw blade, such as not clear protective film can make cutting resistance, damage to equipment and saw blade
9, floating above it is prohibited to break a small wood, more than expected, so as not to damage the mesa sheet caused by the scratch
10, stick bar code must be used when brush dust, avoid the barcode adhesive is not strong to the next working procedure missing
11, after feeding the stack must be neat, avoid damage to the pinch clamp
we promise second-hand woodworking equipment with high quality products, perfect service, welcome friends from all walks of life come to dongguan, the forest industry machinery to visit, guidance and business negotiation.
Custom message
